Knauf Attic Insulation Nationwide

Knauf Attic Insulation: The San Antonio Owner’s Guide

Knauf attic insulation installed in a typical San Antonio home runs between $1,800 and $4,200 depending on square footage, R-value target, and whether we’re topping off existing insulation or pulling out old damaged material first. We stock Knauf EcoBatt and Jet Stream blown-in fiberglass on our trucks, and most San Antonio jobs are completed same day. The usual way homeowners find us: they climb up for holiday decorations, or an HVAC tech points out the insulation looks thin or matted, or the July electric bill finally makes them angry enough to look.

Call (361) 213-9499

Knauf fiberglass insulation works the same way as other premium fiberglass, but the difference is in the batts’ compression and the blown-in product’s settling density. What fails in San Antonio attics is rarely the product itself. It’s almost always installation, age, or a roof leak that compacted the material until it lost its loft and its R-value went with it. If your attic’s cooking, your AC is drowning – let’s fix the cause, not just the bill.

Which Knauf Models This Applies To

We install and match two Knauf product families: EcoBatt (batt insulation in rolls or pre-cut batts) and Jet Stream (loose-fill blown-in fiberglass). EcoBatt comes in R-13, R-19, R-30, and R-38, sized for 2×4, 2×6, and attic joist cavities. Jet Stream is sold by the bag and blown to whatever depth the R-value target calls for. In San Antonio attics, that’s typically R-38 to R-49, which is 13 to 17 inches of settled Jet Stream.

The identifying gotcha with Knauf EcoBatt: the R-value and width are printed on the kraft facing, but facing-up versus facing-down installation matters for vapor behavior in our climate. Unfaced EcoBatt is what we use for attics in San Antonio because a kraft vapor retarder on the wrong side traps moisture against drywall in our humidity swings. If you’re checking what’s already up there, look for the pinkish-brown fiberglass with the Knauf name or the distinctive EcoBatt pattern. Aftermarket equivalents exist, but we’ve had better consistency with Knauf material in Texas heat. It holds its loft longer than budget fiberglass, and the blown-in product settles less in the first year, which means fewer callbacks for us and fewer surprises for you.

Signs Your Knauf Attic Insulation Is Failing

• Upstairs rooms run 8 to 12 degrees warmer than downstairs in summer. The insulation has compacted or was never deep enough to begin with. Fiberglass loses R-value when it compresses, and in a San Antonio attic that regularly hits 140 degrees, that heat pushes straight down through thin spots.
• You can see the tops of the ceiling joists. If attic insulation sits below the joist tops, it’s too thin. For R-38, the material should be well above the joists, not level with them.
• Cold spots near exterior walls or over the garage. Batt insulation shifts over time, especially if anyone’s been up there running cable or checking HVAC ducts. Gaps at the perimeter are where heat dumps in first.
• Dust and fiberglass particles around the attic hatch or ceiling fixtures. Aging Knauf batts shed fibers as the binder breaks down. You’ll see a fine dust on boxes stored in the attic or around can lights.
• Moldy or darkened sections of insulation. That’s a roof leak or a bathroom vent exhausting into the attic instead of outside. Wet fiberglass loses all insulating value and has to come out before new material goes in.

Replacement Cost & What’s Included

For San Antonio homes, here’s what we quote for Knauf insulation replacement or top-off:

• Blown-in Jet Stream top-off, 1,200 sq ft attic to R-38: $1,100 to $1,800
• Full removal of old insulation plus new Jet Stream to R-49: $3,200 to $5,500
• EcoBatt batt install in open attic, 1,200 sq ft to R-38: $2,400 to $3,800
• Air sealing plus blown-in insulation, 1,500 sq ft attic: $2,800 to $4,600

The range comes down to access, how much old material we’re hauling out, and whether your attic needs air sealing first. Every quote includes the written price before work starts, the Knauf material at the specified R-value, full labor, and cleanup. The work carries our 365-Day Done Right Promise in writing: if the insulation settles or fails within a year, we return and fix it free. No third-party warranty runaround. You call Aspen, we show up.

DIY or Call Us?

You can absolutely check the depth of your existing Knauf insulation with a tape measure and look for obvious gaps or water stains. That’s your call, and it’s worth doing before you invite anyone out. What we don’t recommend is renting a blower and going at it yourself unless you’ve done it before. Blown-in fiberglass requires a second person feeding the machine, a respirator rated for particulates, and a steady hand around recessed lights and soffit vents. You can overfill the soffits, block the attic ventilation, and bake your roof deck into an early replacement. Batts seem simple until you’re cutting around truss braces in a 140-degree attic at 2 p.m. in August.

If you’d rather have it measured, quoted, and finished same day by a crew that does this every week, call us at (361) 213-9499. Garrett Sloane or one of our techs will come out, take the attic measurements, and hand you a written price before anything gets installed.

FAQs